Ubiquiti UniFi Switch 8 60W (US-8-60W)

Product Information

USW-Flex — When using PoE passthrough ( Note: this was upgraded to 802.3at PoE+ in a firmware update)

Supports 802.3af/at or 48V Passive PoE to power the switch and can provide 48V (2-pair) PoE passthrough to port 8. You may choose to restrict the collection or use of your personal information in the following ways:PoE passthrough is when a PoE device can receive power and also pass PoE to another downstream device. A common example would be a 24 port PoE switch, feeding an In-Wall-HD access point, with a video camera connected to the In-Wall-HD. The key part is that all three devices are drawing their power from the 24-port PoE switch. In situations like that, you need to be especially careful about what PoE support your switch or voltage and amperage of your PoE injector. pair) PoE output is Off by default. Enabling PoE output (via the UniFi Network Application) requires 24W input power via PoE In or DC input.

Have a small touchscreen on the left side of the device, like the UDM-Pro. This screen shows stats and info about the device, and the network it is on. They also integrate with the UniFi AR feature, which lets you use a phone to virtually see what is connected to each port.Passive 24V and 48V PoE — Ubiquiti’s standard, mostly used on EdgeMAX, AirMAX, and older UniFi devices Ubiquiti calls them “Gen2” but I am going to call them 2nd generation. Whatever you call them, Ubiquiti’s newer UniFi switches split things into a few tiers. There are models which replace the 1st generation switches, and the higher pro and enterprise tiers. All UniFi devices have a Reset button. You can return a device to a factory-default state by holding this for 5-10 seconds (depending on the device), or until the LEDs indicate the restore has begun. Your device must remain powered during this process.

The US-XG-6-PoE has four 1/2.5/5/10 Gbps RJ45 Ethernet ports with PoE++. It also has two 10 Gbps SFP+ interfaces. If you keep having problems with the installation of the firmware you can also try to install it your self directly on the device. To do this we are going to access the device using SSH. EdgeSwitches are older, more traditional managed switches, with command line (CLI) and individual web interfaces for configuration. EdgeSwitches also have optional integration with the UISP software controller. The newer UISP-branded switches are tied closely to the UISP software, have no web interface, but still offer a CLI for manual configuration. I cover EdgeSwitch and UISP hardware briefly below, but I cover them in more detail in my UISP Switch review. Selecting this option will unmanage the device from your UniFi Console and restore the device to a factory default state. UniFi Consoles This will occur if the device was managed by another instance of a UniFi application. This includes cases where the UniFi Console (e.g., Dream Machine Pro, or Cloud Key) was factory restored, because the UniFi device still considers itself as being managed by the 'old' application console, prior to restoration.Have lower fan noise — the non-pro models are fanless. The pros have fans, but are quieter than the 1st generation models. A factory reset is useful for a creating fresh setup of a UniFi Console, or device that was already configured in a managed state. Restoring with the Reset Button Most UniFi switches operate at layer 2, meaning they can handle VLANs but cannot act as a router. The 2nd generation pro and enterprise UniFi switches have some layer 3 features such as static inter-VLAN routing and DHCP, but they require a separate router or firewall for everything else. UniFi L3 switches can’t compete with a true enterprise product from a vendor like Cisco or Juniper. UniFi switches are a fraction of the price and don’t require licensing, so they compete in different markets. As with all network design and purchasing decisions, what matters most is your budget and your use case.

EdgeMAX products are managed with a per-device web interface, or via SSH. These web interfaces are not as polished or pretty as UniFi, but they expose more advanced features than UniFi does. EdgeSwitches also have the full EdgeOS CLI for configuration. If you’re familiar with JunOS or IOS, you’ll be able to figure out your way around. See Ubiquiti’s CLI Command Reference user guide for more details. Do not have a serial console port. All management has to be done over Ethernet in-band. (EdgeSwitches still have console ports!) There’s a lot to cover when it comes to PoE, so I’ll try to keep it as simple as possible. There are 4 main types of PoE to know about: Deciding between UniFi, EdgeMAX, UISP, or some other brand depends on your needs. The right solution varies with what kind of network you are trying to build, and what features you need to accomplish that. If you are comfortable with command line configuration and have complex needs, another vendor is probably a better option. This guide focuses on UniFi switches, but it’s worth noting some EdgeSwitch models are the same hardware as the first generation UniFi switches, with an EdgeOS CLI and UISP instead of the UniFi controller. The newer UISP switches are not as mature, but are worth considering if you want your switch to tie into the UISP NMS and UCRM software. PoE+ devices like the U6-Pro will usually operate with 802.3af input, but they will be unreliable. It’s never a good idea to push past your budget, feed a PoE+ or PoE++ device with a lower tier of PoE, or supply the wrong voltage. Always follow the recommended input power, and never provide less the required power or a different voltage.If you are planning on using PoE passthrough on switches like the USW-Flex, or access points like the In-Wall-HD, you should supply them with the higher-wattage PoE+ or PoE++. Devices with PoE passthrough will usually function when fed with standard 15W PoE, but will not reliably power downstream devices unless they receive their maximum rated power input. For example, the USW-Flex can provide 8W with PoE in, 20W with PoE+ in, and 46W with PoE++ in. Basic layer 3 features like static routing (supported as of firmware version 4.3.13.11253) and inter-VLAN routing. To cache the firmware in your controller you open your controller and go to the settings (lower left gear icon). Search for Firmware and select Device Firmware Cache (or select Updates > Firmware in the settings menu)